10A 24VDC Power Supply - Powers NAC Circuits
- $ 14,799.00
- Brand: FIRE-LITE
- Availability: Out of stock
- SKU: FL-PS10
The PS Series is a line of remote power supplies from Fire•Lite Alarms and is a direct replacement for the FCPS-4FS6/8 series. The FLPS6 is a 6-amp and the FL-PS10...
Tags: categoria:Detección de Fuego , marca:FIRE-LITE , proveedor:Syscom , sku:FL-PS10 , supplier:Syscom , syscom
The PS Series is a line of remote power supplies from Fire•Lite Alarms and is a direct replacement for the FCPS-4FS6/8 series. The FLPS6 is a 6-amp and the FL-PS10 is a 10-amp remote power supply. The power supply includes a battery charger that can be connected to any 12- or 24-volt fire alarm control panel (FACP) or used as a standalone power supply. The PS Series provides 24 VDC power for NACs (Notification Appliance Circuits) configured as Class B or Class A (requires the optional ZNAC-PS card) with multiple synchronization protocol options. The PS Series also provides auxiliary power, constant or resettable, suitable for detectors, annunciators, door holders, and other fire alarm system peripherals. The PS Series cabinet can house two 7 AH or 18 AH batteries and can charge batteries up to 33 AH in a separate cabinet.
Features
- Up to five (6-amp model) or seven (10-amp model) power-limited output circuits that are independently configurable for:
- Class B and/or Class A NACs
- Class B and/or Class A 24V resettable or non-resettable auxiliary power
- Door holder power
- Converts Class B wiring to Class A without losing any outputs using the ZNAC-PS converter card (sold separately)
- Optimal for powering four-wire smoke detectors, annunciators, and other system peripherals requiring regulated power
- Configurable for ANSI® Temporal 3 or Temporal 4 coded output
- UL-listed NAC synchronization using System Sensor®, Wheelock®, Gentex®, or AMSECO® devices
- Synchronization can be triggered from the FACP NAC/remote sync
- outputs, cascaded power supply, or a single or multi-control module that can be housed inside the power supply cabinet
- Ability to cascade up to four power supplies
- Two (6-amp model) or three (10-amp model) inputs/control circuits that can be programmed to any output
- Two Form-C normally closed trouble relays for AC Trouble and General Trouble; ground fault relay available on Canadian models only
- 6 or 10-amp full-load output, respectively, with a maximum of 3 A/circuit
- Individual NAC trouble and power LEDs for diagnostic efficiency
- Trouble history modes for diagnostic support
- Wide-range End-of-Line supervision value (standard: 2K-27K ohms)
- Selectable ground fault detection (enable or disable)
- AC trouble report delay timer
- Fully configurable via built-in DIP switches, no additional software required
- Self-contained in a compact, locking steel gauge cabinet with a corrosion-resistant powder coat chip and scratch-resistant finish
- Cabinet designed with ten double knockouts and a removable door for easy installation and wiring
- Includes integral battery charger capable of charging up to 33 AH batteries
- The cabinet can house two 7 AH or 18 AH batteries
Standards and Codes
- NFPA 72 National Fire Alarm Code
- UL Standard 864 for Control Units for Fire Alarm Systems (NAC expander mode), 10th edition
- UL 1481 Power Supplies for Fire Alarm Systems
- IBC 2009 (when using SEISKIT-MULTI-1)
- CBC 2007 (when using SEISKIT-MULTI-1)
Agency Listings and Approvals
- UL Listed: S2424
- ULC Listed: S2424 (FL-PS6/10C)
- CSFM Approved: 7315-0075:0510
- FDNY Approved
- FM Approved
These listings and approvals apply to the modules specified in this document. In some cases, certain modules or applications may not be listed by certain approval agencies, or the listing may be in process. Consult the factory for the latest listing status.