SYSCOM TOWERS
36 m Floor-Mounted Guyed Tower Kit with Hot-Dip Galvanized STZ45G Section (Guy wires not included).
36 m Floor-Mounted Guyed Tower Kit with Hot-Dip Galvanized STZ45G Section (Guy wires not included).
Couldn't load pickup availability
Key Features
- Product manufactured under ISO 9001:2015 standards
- High elevation / Low cost.
- 100% inspection of section-by-section assembly.
- Hot-dip galvanized in accordance with NMX-H-004-SCFI-2008
- Ideal for coastal areas with high humidity or industrial zones.
Physical Characteristics
- Maximum Axial Load: 500 kg.
- Height: 36 meters (12 sections).
- Wind resistance: 200 km/h.
- Anti-corrosion protection: Hot-dip galvanized (NMX-H-004-SCFI-2008).
- Application: Outdoor (Humid Areas).
| Quantity | Model | Description |
|---|---|---|
| 12 | STZ45G | Tower section, 45 cm face width. |
| 1 | SCZ45G | Tower top, 45 cm, with lightning rod set screw. |
| 1 | SBZ45G | Base for 45 cm tower. |
| 1 | SAB45G | Anchor for 35/45 tower base. |
| 4 | SJB45G | Guy wire attachment bracket. |
| 3 | SAZ45G | Ground anchor for guy wire. |
| 24 | CUELLO-14-HDG | Guy wire thimble |
| 72 | NUDO-14-FJG | 1/4" wire rope clip |
- Guy wire: 450 meters of 1/4" guy wire (SRET-635-CAM) or larger diameters are recommended. SRET-635-CAM
- Turnbuckles: 12 5/8" x 9" turnbuckles are recommended. TEN5/8X9OGJ or TEN5/8X9OQJ
- Warning: Using non-standard accessories voids the equipment warranty
Signaling/Lighting System (Not included)
| Quantity | Model | Description |
|---|---|---|
| 2 | EIGSLSE | Autonomous LED strobe with photocell, solar panel, and battery. Type L810. |
| 2 | HLU3R2 | Mount for EIGSLSE obstruction light |
* Signaling standards dictate that the tower must be painted in 7 alternating stripes of equal size; 4 orange-red and 3 white.
Lifeline System (Not included)
| Quantity | Model | Description |
|---|---|---|
| 1 | SHE-LV | Pair of mounting brackets |
| 2 | S-GULV | Line guide |
| 39 | SRET-338CAM | 3/8" cable |
| 6 | NUDO-38FJG | 3/8" forged wire rope clip |
| 2 | CUELLO-38-HDG | 3/8" thimble |
| 1 | TRY-ACC-SLIDER | (Optional) Safety slider for installer. |
| 1 | SYS-USA7B | (Optional) Suspension harness. |
* NOM-009 mandates the use of fall arrest systems when working on a structure.
Recommended Grounding System (Not included)
| Quantity | Model | Description |
|---|---|---|
| 1 | TG45AB | 45A grounding electrode with electrode, filter, and H2Ohm compound |
| 1 | S610 | Plastic inspection pit. |
| 3 | TGCR11 | Eye connector |
| 2 | TGAB18 | Rod connector |
| 1 | TGBUSG10 | Grounding bus bar with 1000A capacity insulators (no cabinet) |
* It is recommended to use 4 AWG insulated copper wire SLY-287-GRN for grounding the electrode to the tower. For equipment on the tower, 6 AWG SLY-291-GRN can be used.
Recommended Basic Lightning Protection System (Not included)
| Quantity | Model | Description |
|---|---|---|
| 1 | TGTDPC | Lightning rod tip with aluminum mast (MASTIL1.2) |
| 1 | TG45AB | 45 Amp. electrode with one bag of impedance improvement compound (H2OHM), compass, and level. |
| 1 | S610 | Small plastic inspection pit. |
| 1 | ANTIOX | Terminal protection spray. |
| 3 | TGCR11 | Eye connector. |
| 2 | TGAB18 | Rod connector. |
| 24 | TGAC114 | Tower insulator. |
*The dipole-type tip offers a 72° protection cone below the coil. Recommended for areas with low lightning incidence.
*2/0 AWG copper wire is recommended for integration SLY-346-BLK. Assuming the electrode is installed at a maximum of 3 meters from the tower, approximately 8 meters are needed.
See the Grounding + Lightning rod connection diagram in the following DIAGRAM.
Recommendations
- Ensure the installation is performed by a trained professional.
Representative Diagram: Guy Wire Installation Version 2.0
Installation Images


