SYSCOM TOWERS
39 m Height Guyed Floor Tower Kit with Hot-Dip Galvanized STZ45G Section. (Guy wires not included).
39 m Height Guyed Floor Tower Kit with Hot-Dip Galvanized STZ45G Section. (Guy wires not included).
Couldn't load pickup availability

Key Features:
- Product manufactured under ISO 9001:2015 standards.
- High elevation / Low cost.
- 100% inspection of section-by-section assembly.
- Hot-dip galvanized in accordance with NMX-H-004-SCFI-2008.
- Ideal for high-humidity coastal zones or industrial areas.
Physical Specifications:
- Maximum Axial Load: 500 kg.
- Height: 39 meters (13 sections).
- Wind resistance: 200 km/hr.
- Anti-corrosion protection: Hot-dip galvanized (NMX-H-004-SCFI-2008).
- Application: Outdoor (Humid zones).
- 13 - STZ45G: 45 cm face width tower section.
- 1 - SCZ45G: 45 cm tower top cap with lightning rod clamp.
- 1 - SBZ45G: Base for 45 cm tower.
- 1 - SAB45G: Anchor for 35/45 tower base.
- 5 - SJB45G: Guy wire clamp.
- 3 - SAZ45G: Floor anchor for guy wire.
- 30 - CUELLO-14-HDG: Thimble for guy wire.
- 90 - NUDO-14-FJG: 1/4' wire rope clip.
Guy wire is not included. We recommend 600 meters of 1/4' guy wire (SRET-635-CAM) or larger diameters.
Turnbuckles are not included. We recommend 15 turnbuckles of 5/8' x 9' (TEN5/8X9OGJ or TEN5/8X9OQJ).
*Failure to use installation accessories such as clamps, tower base, tower anchor, or guy anchors will void the equipment warranty, and any additional modifications are the responsibility of the installer.
- 1 - SHE-LV: Pair of mounting brackets.
- 2 - S-GULV: Line guide.
- 42 - SRET-338CAM: 3/8' cable.
- 6 - NUDO-38FJG: 3/8' forged wire rope clip.
- 2 - CUELLO-38-HDG: 3/8' thimble.
- 1 - TRY-ACC-SLIDER: (Optional) Safety Slider for installer.
- 1 - SYS-USA7B: (Optional) Full-body harness.
*NOM-009 requires the use of systems that arrest accidental falls from a structure.
- 1 - TG45AB: 45A grounding electrode with filter and H2Ohm compound.
- 1 - S610: Plastic inspection well.
- TGCR11: Eye connector.
- 2 - TGAB18: Rod connector.
- 1 - TGBUSG10: 1000A capacity grounding busbar (no cabinet).
*We recommend 4 AWG jacketed copper wire (SLY-287-GRN) for grounding from the electrode to the tower. For equipment on the tower, 6 AWG (SLY-291-GRN) can be used.
- 1 - TGTDPC: Lightning rod tip with aluminum mast (MASTIL1.2).
- 1 - TG45AB: 45 Amp electrode with impedance-improving compound (H2OHM), compass, and level.
- 1 - S610: Small plastic inspection well.
- 1 - ANTIOX: Protective spray for terminals.
- 3 - TGCR11: Eye connector.
- 2 - TGAB18: Rod connector.
- 26 - TGAC114: Tower insulator.
*The dipole-type tip offers a 72° protection cone below the coil. Recommended for areas with low lightning incidence.
*We recommend 2/0 gauge copper wire for integration (SLY-346-BLK). Assuming the electrode is installed at a maximum of 3 meters from the tower, approx. 8 meters are used.
View Grounding + Lightning Protection connection diagram: DIAGRAM
Recommendations:
- Ensure installation is performed by a trained professional.
- Establish a maintenance plan for checking guy wire tension and hardware tightening.
- Do not install solar panels higher than 6 meters. Check compatibility between solar cells and mounts.
- A stress analysis must be performed when an eccentric load is placed on the tower. This can cause excessive twisting and bending, leading to structural failure.
- The tower must be painted orange-red and white, in 7 bands of equal height, starting and ending with orange-red (SYSCOM does not perform painting).
- It is recommended to illuminate the tower at the top with at least one red lamp.
Representative Diagram: Guy Wire Installation Version 2.0
Installation Images


