SYSCOM TOWERS
9 m Floor-Mounted Guyed Tower Kit with Hot-Dip Galvanized STZ45G Section (Guy wire not included).
9 m Floor-Mounted Guyed Tower Kit with Hot-Dip Galvanized STZ45G Section (Guy wire not included).
Couldn't load pickup availability
Key Features
- Product manufactured under ISO 9001:2015 standard
- High elevation / Low cost.
- 100% Section-by-section assembly inspection.
- Hot-dip galvanized in accordance with NMX-H-004-SCFI-2008
- Ideal for high-humidity coastal areas or industrial zones.
Physical Characteristics
- Maximum Axial Load: 500 kg.
- Height: 9 meters (3 sections).
- Wind resistance: 200 km/h.
- Anti-corrosion protection: Hot-dip galvanized (NMX-H-004-SCFI-2008).
- Application: Outdoor (Humid zones).
Includes the following components
| Quantity | Model | Description |
|---|---|---|
| 3 | STZ45G | Tower section with 45 cm face width. |
| 1 | SCZ45G | 45 cm tower top with lightning rod set screw. |
| 1 | SBZ45G | Base for 45 cm tower. |
| 1 | SAB45G | Anchor for 35/45 tower base. |
| 1 | SJB45G | Guy wire support flange. |
| 3 | SAZ45G | Floor anchor for guy wire. |
| 6 | CUELLO-14-HDG | Thimble for guy wire |
| 18 | NUDO-14-FJG | 1/4" wire rope clip. |
Guy wire not included. 42 meters of 1/4" guy wire (SRET-635-CAM) or larger diameters are recommended.
Turnbuckles not included. 3 turnbuckles of 5/8" x 9" are recommended (TEN5/8X9OGJ or TEN5/8X9OQJ).
Failure to use installation accessories such as flanges, tower base, tower anchor, or guy wire anchors will result in the loss of the equipment warranty, and any additional modification is the responsibility of the installer.
Complementary accessories (Not included)
Signaling/Lighting System (Not included)
| Quantity | Model | Description |
|---|---|---|
| 2 | EIGSLSE | Autonomous LED strobe with photocell, solar panel, and battery. L810 type. |
| 2 | HLU3R2 | Mounting for EIGSLSE obstruction lamp |
* Signaling standards dictate that the tower must be painted in 7 equal-sized bands; 4 reddish-orange bands and 3 white bands.
Lifeline system (Not included)
| Quantity | Model | Description |
|---|---|---|
| 1 | SHE-LV | Pair of fastening brackets |
| 1 | S-GULV | Line guide |
| 12 | SRET-338CAM | 3/8" cable |
| 6 | NUDO-38FJG | 3/8" forged clip |
| 2 | CUELLO-38-HDG | 3/8" thimble |
| 1 | TRY-ACC-SLIDER | (Optional) Safety slider for installer. |
| 1 | SYS-USA7B | (Optional) Suspension harness. |
*NOM-009 mandates the use of systems that arrest accidental falls on a structure.
Recommended Grounding System for Tower and mounted equipment (Not included)
| Quantity | Model | Description |
|---|---|---|
| 1 | TG45AB | 45A grounding electrode with electrode, filter, and H2Ohm compound |
| 1 | S610 | Plastic access box. |
| 3 | TGCR11 | Eye connector |
| 2 | TGAB18 | Rod connector |
| 1 | TGBUSG10 | 1000A capacity grounding bus bar with insulators (without enclosure) |
* The use of 4 AWG jacketed copper cable (SLY-287-GRN) is recommended for grounding from the electrode to the tower. For equipment on the tower, 6 AWG cable (SLY-291-GRN) can be used.
Basic Lightning Protection System Recommended for Tower (Not included)
| Quantity | Model | Description |
|---|---|---|
| 1 | TGTDPC | Lightning rod tip with aluminum mast (MASTIL1.2) |
| 1 | TG45AB | 45 Amp electrode with a bag of impedance-improving compound (H2OHM), compass, and level. |
| 1 | S610 | Small plastic access box. |
| 1 | ANTIOX | Terminal protection spray. |
| 3 | TGCR11 | Eye connector. |
| 2 | TGAB18 | Rod connector. |
| 6 | TGAC114 | Tower insulator. |
*The dipole-type tip offers a 72° protection cone below the coil. It is recommended for areas with low lightning incidence.
*2/0 gauge copper cable is recommended for integration (SLY-346-BLK). Considering an electrode installation at a maximum of 3 meters from the tower, approx. 8 meters are used.
See the Physical Ground + Lightning Rod connection diagram in the following DIAGRAM.
Recommendations
- Ensure that the installation is performed by a trained professional.
- Schedule a maintenance plan to check guy wire tension and tighten hardware.
- Do not install solar panels at a height greater than 6 meters. Check compatibility between solar cells and mounts.
- A stress study must be performed when an eccentric load is placed on the tower. This can cause excessive torsion and bending in the tower, leading to structural failure.
- The tower must be painted in orange-red and white tones, in 7 stripes of equal height starting and ending in orange-red (SYSCOM does not perform tower painting work).
- It is recommended to illuminate the tower at least at the tip with a red lamp.
Representative Diagram: Guy Wire Installation Version 2.0
Installation Images


