SYSCOM TOWERS
18m Roof-Mounted Guyed Tower Kit with Hot-Dip Galvanized STZ30G Section (Guy wire not included).
18m Roof-Mounted Guyed Tower Kit with Hot-Dip Galvanized STZ30G Section (Guy wire not included).
Couldn't load pickup availability

Key Features
- Standard: ISO 9001:2015
- High Elevation / Low cost
- 100% Section-by-Section Assembly Inspection
- Galvanization: Hot-dip (NMX-H-004-SCFI-2008)
- Ideal for high-humidity coastal zones or industrial areas
Physical Characteristics
- Maximum Axial Load: 200 Kg
- Height: 18 meters (6 sections)
- Wind Resistance: 200 km/hr
- Anti-corrosion protection: Hot-dip galvanization (NMX-H-004-SCFI-2008)
- Application: Outdoor (Humid zones)
- Quantity: 6 - STZ30G - 30 cm face width tower section
- Quantity: 1 - SCZ30PG - 30 cm tower top with set screw for lightning rod
- Quantity: 1 - SBA30G - Base for 30 cm tower
- Quantity: 1 - SAB30G - Anchor for tower base
- Quantity: 3 - SJB30G - Guy wire clamp flange
- Quantity: 3 - SAP01G - Slab or wall anchor for guy wire
- Quantity: 18 - CUELLO-14-HDG - Thimble for guy wire
- Quantity: 54 - NUDO-316-FJG - 3/16' cable clamp
Guy wire not included. 190 meters of 1/8' guy wire (SRET-318-CAM) or larger diameters are recommended.
Turnbuckles not included. 9 1/2' x 6' turnbuckles are recommended. (TEN1/2X6OGJ or TEN1/2X6OQJ).
**Failure to use installation accessories such as flanges, tower base, tower anchor, or guy anchors will void the equipment warranty, and any additional adaptation is the responsibility of the installer.**
- Signaling/Lighting System (Not included)
- Quantity: 1 - SHE-LV - Pair of mounting brackets
- Quantity: 1 - S-GULV - Line guide
- Quantity: 21 - SRET-338CAM - 3/8' cable
- Quantity: 6 - NUDO-38FJG - 3/8' forged clamp
- Quantity: 2 - CUELLO-38-HDG - 3/8' thimble
- Quantity: 1 - TRY-ACC-SLIDER - (Optional) Safety carriage for installer
- Quantity: 1 - SYS-USA7B - (Optional) Suspension Harness
*NOM-009 mandates the use of systems that prevent accidental falls on a structure.
- Quantity: 1 - TG45AB - 45 A grounding electrode with electrode, filter, and H2Ohm compound
- Quantity: 1 - S610 - Plastic inspection box
- Quantity: 3 - TGCR11 - Eye connector
- Quantity: 2 - TGAB18 - Rod connector
- Quantity: 1 - TGBUSG10 - Bonding bar with 1000A capacity insulators (No cabinet)
* 4 AWG coated copper cable (SLY-287-GRN) is recommended for grounding the electrode to the tower. For equipment on the tower, 6 AWG (SLY-291-GRN) can be used.
- Quantity: 1 - TGTDPC - Corona dipole lightning rod tip
- Quantity: 1 - TG45AB - 45 Amp electrode. With one bag of enhancing compound (H2OHM), compass, and level
- Quantity: 1 - S610 - Small plastic inspection box
- Quantity: 1 - ANTIOX - Terminal protection aerosol
- Quantity: 3 - TGCR11 - Eye connector
- Quantity: 2 - TGAB18 - Rod connector
- Quantity: 12 - TGAC - Down conductor cable insulator
*The dipole tip offers a 72° protection cone below the coil. It is recommended for areas with low lightning incidence.
*2/0 gauge copper cable is recommended for integration (SLY-346-BLK). Considering an electrode installation at a maximum of 3 meters from the tower, approx. 8 meters are used.
See Grounding + Lightning Rod connection diagram: DIAGRAM
Recommendations
- Ensure the installation is performed by a trained professional
- Schedule a maintenance plan for checking guy tension and adjusting hardware
- Do not install solar panels at heights over 6 meters. Check compatibility between solar cells and mounts
- A stress analysis must be performed when an eccentric load is placed on the tower. This can cause excessive torsion and bending in the tower, leading to structural failure
- The tower must be painted in orange-red and white, in 7 stripes of equal height, starting and ending with orange-red (SYSCOM does not provide tower painting services)
- It is recommended to illuminate the tower at least at the tip with a red lamp
Representative Diagram: Guy Wire Installation Version 2.0
Installation Images


