Key Features
- Product manufactured under ISO 9001:2015 standards
- High elevation / Low cost
- 100% section-by-section assembly inspection
- Electrolytic galvanization in accordance with ASTM B-633 standards
- Ideal for dry, corrosion-free zones
Physical Characteristics
- Maximum Axial Load: 200 kg
- Height: 3 meters (1 section)
- Wind resistance: 200 km/hr
- Anti-corrosion protection: Electrolytic Galvanization (ASTM B-633)
- Application: Outdoor (Desert or low-humidity zones)
Includes the following components
- 1 STZ30 - 30 cm face width tower section
- 1 SCZ30P - 30 cm tower top with set screw for lightning rod
- 1 SBA30 - 30 cm tower base
- 1 SAB30 - Tower base anchor
- 1 SJB30 - Guy wire mounting bracket
- 3 SAP01 - Slab or wall anchor for guy wire
- 6 CUELLO-14-HDG - Thimble for guy cable
- 18 NUDO-316-FJG - 3/16" wire rope clip
Complementary accessories (Not included)
Does not include guy cable. 20 meters of 1/8" guy cable SRET-318-CAM or larger diameters are recommended
Does not include turnbuckles. 3 1/2" x 6" turnbuckles TEN1/2X6OGJ or TEN1/2X6OQJ are recommended
**FAILURE to use installation accessories such as brackets, tower base, tower anchor, or guy anchors will void the equipment warranty, and any additional modifications are the responsibility of the installer.**
Signaling/Lighting System (Not included)
- 2 EIGSLSE - Autonomous LED strobe with photocell, solar panel, and battery. L810 type
- 2 HLU3R2 - Mounting for EIGSLSE obstruction light
*Signaling standards dictate that the tower must be painted in 7 equal-sized bands; 4 orange-red bands and 3 white bands
Lifeline System (Not included)
- 1 SHE-LV - Pair of mounting hardware
- 1 S-GULV - Guide for line
- 5 SRET-338 - 3/8" cable
- 6 NUDO-38FJG - 3/8" forged wire rope clip
- 2 CUELLO-38-HDG - 3/8" thimble
- 1 TRY-ACC-SLIDER - (Optional) Safety Slider for Installer
- 1 SYS-USA7B - (Optional) Suspension Harness
*NOM-009 mandates the use of systems that prevent accidental falls on a structure
Recommended Grounding System for Tower and Mounted Equipment (Not included)
- 1 TG45AB - 45 A grounding electrode with electrode, filter, and H2Ohm compound
- 1 S610 - Plastic inspection box
- 3 TGCR11 - Eye connector
- 2 TGAB18 - Rod connector
- 1 TGBUSG10 - 1000A capacity grounding busbar with insulators (without cabinet)
* It is recommended to use 4 AWG coated copper cable SLY-287-GRN for connecting the electrode to the tower. For equipment on the tower, 6 AWG SLY-291-GRN can be used
Recommended Basic Lightning Protection System for Tower (Not included)
- 1 TGTDPC - Lightning rod tip with aluminum mast (MASTIL1.2)
- 1 TG45AB - 45 Amp electrode with one bag of impedance-improving compound (H2OHM), compass, and level
- 1 S610 - Small plastic inspection box
- 1 ANTIOX - Spray for terminal protection
- 3 TGCR11 - Eye connector
- 2 TGAB18 - Rod connector
- 2 TGAC - Tower insulator
*The dipole-type tip offers a 72° protection cone below the coil. Recommended for areas with low lightning incidence
*2/0 gauge copper cable is recommended for integration SLY-346-BLK. Assuming the electrode is installed at a maximum distance of 3 meters from the tower, approx. 8 meters are used
DIAGRAM of Grounding + Lightning protection connection
Recommendations
- Ensure that the installation is performed by a qualified professional
- Schedule a maintenance plan to check guy wire tension and tighten hardware
- Do not install solar panels more than 6 meters high. Check compatibility between solar cells and mounts
- A stress analysis must be performed when placing an eccentric load on the tower. This can cause excessive torque and bending, leading to structural failure
- The tower must be painted in orange-red and white, in 7 bands of equal height, starting and ending in orange-red (SYSCOM does not perform painting services)
- It is recommended to illuminate the tower at least at the top with a red light
